Monthly Archives: May 2011

Power Steering Service

Posted on May 23, 2011 by wade

For most of us, it is hard to remember life without power steering – cranking those great big steering wheels? It was a pretty good workout. Now power steering is standard. The heart of any power steering system is its pump. The pump pressurizes the power steering fluid that provides assist for steering. Most pumps are driven by a belt that is run by the engine – a few are electrically powered. A high-pressure hose passes fluid from the pump to the steering gear. A low pressure hose returns the fluid back to the pump.

These hoses can develop leaks, so it is a good idea to inspect them at every oil change. Low fluid can damage the power steering pump. That is why fluid level is on the checklist for a full-service oil change. The fluid needs to be compatible with the hoses and seals, so check your owners’ manual for the right type – or just ask your service technician.

The fluid cleans, cools and lubricates the power steering system. It breaks down as the years go by and collects unwanted moisture, so it needs to be replaced from time to time. Many manufacturers specify power steering service intervals. Unfortunately, this important service is sometimes left off the maintenance schedule. So, when in doubt, every 25,000 miles/40,000 km or two years is a good fallback. Your Prineville or Madras service center will use a detergent to clean the system, flush out the old fluid and replace it with the good stuff.

Here are some warning signs of trouble with your power steering: It’s harder to turn the wheel, there’s erratic power assist, you hear loud whining coming from the pump (which may be difficult to hear over the loud whining coming from the backseat), you have to top-off the fluid frequently, or you hear squealing belts. Remember to never hold the steering wheel to the far right or left for more than a few seconds at a time. That will wear out your pump real fast.

Other steering components can be bent or damaged from wear or hard knocks. Ball-joint, idler-arm, steering-gear, steering-knuckle and tie rod to name a few. Warning signs here are steering play, wandering, uneven tire wear, and off-center steering wheel. An annual alignment check at Wade Bryants auto repair & service center in Bend will reveal bent or damaged steering components.

Most SUV’s, pick-ups and rear-wheel-drive cars need regular front-wheel-bearing service.

The bearings should be cleaned and inspected. If they are excessively worn, they need to be replaced. The bearings are then repacked in clean grease. It’s also recommend the wheel-seal be replaced when the bearings are serviced. Like everything else, check your owners’ manual maintenance schedule. It’s usually required around every two years or 40,000 miles/64,000 km. If you drive through water, the bearings will need service more often.

Share
Posted in Steering | 1 Comment

PCV Valve Replacement

Posted on May 23, 2011 by wade

The energy from exploding fuel is what powers your engine. But some of the vapors from the explosions escape into the lower part of the engine, called the crankcase. The crankcase is where your engine oil hangs out. These gases are about 70% unburned fuel. If the gases were allowed to stay in the crankcase, they would quickly contaminate the oil and turn it to sludge. Sludge is one of the biggest enemies of your engine, clogging it up, eventually leading to expensive failures. Also, the pressure build up would cause seals and gaskets to blow out. Therefore, these gases need to be vented out.

Gasoline engines used to simply have a hose that let the poisonous fumes vent out into the air. In 1963, the federal government required gas engines to have a special one-way valve installed to help reduce dangerous emissions. Diesel engines are not required to have these valves.

The positive crankcase ventilation, or PCV, valve routes crankcase gases through a hose and back into the air intake system where they are re-burned in the engine. Fresh, clean air is brought into the crankcase through a breather tube. It’s really a pretty simple system, but does an important job. The re-circulating air removes moisture and combustion waste from the crankcase, preventing sludge. This extends not only the life of your oil, but the engine as well. The PCV relieves pressure in the crankcase, preventing oil leaks.

Eventually, the PCV valve can get gummed up. Then it can not move enough air through the engine to keep it working efficiently. If the PCV valve is sticking enough, you could have oil leaks, excess oil consumption and a fouled intake system. If you experience hesitation or surging or an oil leak, it may be a sign of PCV value problems. Your owners’ manual may give a recommendation for when the PCV valve should be replaced – usually between 20,000 mi/32,000 km and 50,000 mi/80,000 km. Unfortunately, some manufacturers don’t list a recommendation in the manual, so it can be easy to overlook.

Many PCV system problems can be diagnosed with a visual inspection. Fortunately, PCV valve replacement is both quick and inexpensive. Proper oil changes will greatly extend the life of the PCV valve. Skipping a few recommended oil changes can allow varnish and gum to build up in the valve, reducing its efficiency. So now when your Bend service technician tells you its time to replace your PCV valve, you will know what he’s talking about. If you have had your car for a while and this is the first you’ve ever heard of a PCV value, ask your tech to check yours out or call Wade Bryants auto repair & service center at 541 389 2465.

Share
Posted in Parts | 1 Comment

Suspension Service

Posted on May 23, 2011 by wade

When you hear the word ‘suspension‘, you may think back to those energetic days of grade school. Well, your car’s suspension is actually a good thing because it keeps your car up off the road and helps provide a comfy ride. It needs to keep your wheels firmly planted over bumps and through curves. Your suspension system has many parts. If you look under your car, it’s basically everything that connects your wheels to the car’s frame. These are heavy duty parts that do a lot of work. They need to be inspected for damage and excessive wear at least once a year. A good time for this is when you get your annual alignment service.

Here are some warning signs that your suspension may have problems:

  • the car pulls to one side;
  • it wanders;
  • the steering is erratic;
  • you see uneven tire wear;
  • you experience a poor ride or handling;
  • you see oil leaking from shocks

. . . you get the picture. You just don’t feel in control when you’re driving.

Some suspension parts just wear out with use. Shocks and struts eventually lose their ability to control your ride. Wheel bearings need to be repacked every couple of years. And some suspension pieces need to be lubricated when you get your oil changed. Your service advisor can oversee an inspection and tell you what problems you may have.

If you’re in an accident, your suspension can be damaged or knocked out of alignment. Even a minor accident, like hitting a curb around Bend or even a large rock can mess things up. With a minor accident it’s tempting to just get an alignment or wheel balance to correct the problem. But if there’s some damage, a simple alignment won’t actually fix the problem, and you’ll just have to align it again after the repairs are made. So if you have an accident, get your suspension system inspected right away. Suspension problems should be fixed immediately because they can lead to unsafe handling.

One big cause of suspension damage is potholes – those nasty magnets that seem to draw our tires right into them. Here are some tips for avoiding damage from potholes: First, keep your tires at their full air pressure. That gives tires their maximum resiliency and will hopefully keep your wheels or other suspension parts from crunching on a big hole. Next, just pay attention. When you see a hole you can’t miss, slow down before you hit it. Driving at a slower speed will limit the damage, and may keep your drink from spilling. But don’t brake directly over the pothole. That will cause the car’s weight to shift forward and add to the potential damage.

So don’t put off an inspection of your suspension. We promise the principal won’t be involved.

Wade Bryants auto repair & service center
Give us a call today at 541 389 2465.
Or stop by at 324 se 9th st, Bend, Oregon 97702

Share
Posted in Shocks & Struts | 1 Comment

Air Conditioning Service

Posted on May 23, 2011 by wade

Do you hear loud noises under the hood when you turn on your air conditioner? Do you only get cool air sporadically? If so, it is time to get your air conditioner checked. It’s real easy to take your car’s air conditioner for granted. Just push the right buttons and out comes cool, dry, clean air. But your air conditioning system needs attention from time to time to help it keep its cool.

When most people hear the words “air conditioning problems”, it sends a shiver up their spine. That is because the air conditioning system is fairly complex. It has a lot of parts and when it’s broken, it’s expensive to repair.

What things can we do to prevent air conditioning breakdowns?

A common cause of air conditioning failure is leaks. Water and air can leak into the system. The system doesn’t work as well with air in it. And water can cause rust that leads to damage of the A/C components. Also, refrigerant, the stuff that makes the air cold, can leak out, reducing the efficiency of the system, making it work harder to cool the air. Periodically evacuating the air conditioning system and recharging it keeps the proper amount of clean refrigerant in the system so it cools better and lasts longer.

You should also run the air conditioner regularly, even during Oregon winters, so that it lubricates itself and keeps the seals from drying out, which leads to leaks. Your owner’s manual will have recommendations for how often to service your air conditioner. Of course, if it’s not working right, now is the time to get it checked. Many Redmond service centers can inspect and test your air conditioning and offer evacuation and recharge services. We recommend Wade Bryants auto repair & service center in Bend. See wadebryants@mechanicnet.com for address and phone number. A quick inspection can help you avoid having to bring your air conditioner in for major repairs.

New environmental laws have stopped the manufacture of Freon, a refrigerant that was common in cars made before 1993. There is a very limited supply of Freon so the price is very steep. It may not be worth its weight in gold, but it probably is worth its weight in silver. If you have an older vehicle that uses Freon, you may want to consider having it retrofitted to use the new R134-A refrigerant. It will pay for itself in the long run. So, if your AC is just a lot of hot air, take it to a Sunriver automotive service center for an inspection.

Share
Posted in Air Conditioning | Leave a comment

Severe Service Requirements

Posted on May 23, 2011 by wade

A lot of our viewers have asked whether or not they should use their severe service maintenance schedule, which is listed in their car owners’ manual. It can be confusing. Let’s clear the air on this subject. Cricket Killingsworth is from QMI/Heartland, a manufacturer of automotive products and fluids. She’s been in the automotive business for 20 years and is a speaker, a trainer, and a writer. Cricket says there’s so much confusion on this topic because, “Most owners’ manuals actually have two maintenance schedules. Sometimes these are called ‘regular service’ and ‘severe service’. Sometimes they’re simply called Schedule 1 and Schedule 2. A severe service schedule recommends that things like an oil change, air filter replacement, and transmission service be done more often: either in fewer miles or in less time.

Manufacturers create these specific schedules for each vehicle they make. So there isn’t one generic schedule that applies to all cars. In addition to your owners’ manual, Bend automotive repair centers subscribe to information services that provide the maintenance schedules for every vehicle – so they can help you know when to take care of needed services. Below is a typical definition for severe service.

  • Most trips are less than four miles
  • Most trips are less than ten miles and outside temperatures are below freezing
  • You drive in very hot weather
  • The engine is at low speed most of the time (not on the highway)
  • Stop and go driving
  • You operate your vehicle in dusty or muddy conditions
  • You tow a trailer, regularly carry heavy loads or carry a car-top carrier

It’s common sense: Just a few minutes at freeway speeds allows the moisture in the oil to evaporate. Very short trips, or trips of less than ten miles when it’s very cold, don’t allow the engine to heat up enough to get rid of the water. And water in the oil leads to damaging sludge. Also, towing and heavy loads raise operating temperatures and cause fluids to breakdown more quickly. Dusty and muddy driving means that more dirt will get past the air filter to contaminate the fuel system and engine oil.

The bottom line is that you need to decide for yourself if the regular or severe service schedule is right for you, based on your driving. Look at your owners’ manual, or talk with your Wade Bryants auto repair & service center service advisor who can help you know which schedule to follow. Wade Bryants auto repair & service center is located at 324 se 9th st, Bend Oregon.,

Here is what a fleet manager said recently: “Since city miles are generally tougher on vehicles than highway miles, we use the manufacturer’s severe service schedule as the basis for our preventative maintenance program. We massage those schedules over time, increasing or decreasing the service intervals so that they make the most sense. There is a little bit of art to go along with the science.

Make an honest evaluation of your driving habits. Unless you do mostly Oregon highway driving in moderate weather, you’ll likely have a fairly good amount of severe service mixed in. Some people just want to play it safe and follow the severe service recommendations, rather than analyzing how they drive each month.

Share
Posted in Maintenance | Leave a comment

Vehicle Warranties

Posted on May 23, 2011 by wade

If you own a Oregon vehicle with a warranty, beware! Many dealers and manufacturers suggest that you need to get your maintenance services at a dealership in order to keep your warranty. That simply isn’t true! You can have your vehicle serviced at your trusted, local service center without affecting your warranty. A federal law, called the Magnuson-Moss Warranty Act, prohibits a manufacturer from voiding your warranty just because you got parts or services from a non-dealer. In fact, a manufacturer can’t require you to use their brand of oil filters, lubricant, or any other part in order to maintain your warranty protection. This protection is true for aftermarket extended warranties purchased on new or used vehicles. This protection also applies to leased vehicles. There are similar laws in Canada as well.

If a manufacturer can prove that the replacement parts or service lead to a vehicle failure, they can void a portion of the warranty. Of course, Wade Bryants auto repair & service center uses quality parts and fluids that meet or exceed manufacturers’ specifications. (See wadebryants@mechanicnet.com.) A lot of people do not know that service centers subscribe to data services that tell them exactly which parts and fluids meet manufacturers’ specifications. These services are updated constantly so that your Redmond automotive service center always knows what you need for your car. You can be assured that your vehicle will receive high quality replacement parts that’ll keep you safely on the road.

Proper maintenance is so important to safety. It can also prevent costly repairs and save you money over the long haul. Just because you don’t have to go to a dealer to get your maintenance service performed doesn’t mean that you don’t need to have it done at all. In fact, some protections from your warranty require that scheduled maintenance be performed. If you miss having important work done, you may lose some warranty coverage. Refer to your owners’ manual and vehicle warranty for more details. And keep good records of the work you’ve had done.

The protection you receive under the Magnuson-Moss Warranty Act can save you hundreds of dollars each year. The average hourly labor rate for service is nearly twenty percent lower at independent service centers such as Wade Bryants auto repair & service center. We are conveniently located at 324 se 9th st in Bend. So why go anywhere else?

Share
Posted in Warranty | Leave a comment

Braking News: Keep Your Stopping Power

Posted on May 23, 2011 by wade

Richard Petty once told AutoNetTV, “You’ve gotta have good brakes. If you’ve got good brakes you can keep yourself out of a lotta trouble.”

That’s why a regular brake inspection is on every Bend car’s maintenance schedule. An inspection at Wade Bryants auto repair & service center will check your brake system and let you know if there are any problems.

Of course, if you’re having trouble with your brakes, get your car into Wade Bryants auto repair & service center right away. Here are some symptoms to watch for:

  • Low or spongy brake pedal
  • Hard brake pedal
  • A brake warning light that stays on
  • Constantly squealing or grinding brakes
  • Vibrations or clunking sounds when you apply your brakes

If you are experiencing any of these, it’s time to get your brakes checked.

There are two types of brakes: disc and drum. Disc brakes have a rotor that’s attached to the axle. Calipers straddle the rotor, kind of like the brakes on a bicycle.

Drum brakes are more common on back wheels. Both types have pads or shoes that press against the brakes and slow the vehicle. Brake pads and shoes are made out of very tough material to withstand the heat and force generated when stopping your car. Eventually, they wear out with use, and become too thin and need to be replaced.

If the brake pads wear away completely, you can damage the rotors. The calipers can grind grooves in the rotor. Then the rotor must either be resurfaced or replaced. That’s not only expensive, but also dangerous because your vehicle won’t stop as quickly. Sometimes rotors warp or crack and must be replaced.

Brake service will also include a check of your brake fluid. When the brakes are applied, the pressure in the fluid actives the brake pads or shoes. Not enough fluid means not enough pressure to brake properly. Also, water builds up in the brake fluid over time, which leads to corrosion, leaks and brake damage, and with hard use, the brakes could severely fade or even fail. You should change the brake fluid when your manufacturer recommends to avoid these problems.

There are different grades of brake pads; good, better and best. Higher grades cost more, but give better braking performance and smoother operation. It’s OK to upgrade your brake pads. But, never use a grade that’s lower than what the manufacturer recommends.

So, be sure to properly maintain your brakes, because it’s a lot cheaper than paying the body shop after an accident.

Come in to Wade Bryants auto repair & service center for an brake inspection before damage occurs. You can call ahead for an appointment by calling 541 389 2465.

Share
Posted in Brakes | Leave a comment

What To Do After You Buy a Used Vehicle in Bend

Posted on May 23, 2011 by wade

So you’ve bought a used car in the Bend area. How do you know what you’re getting? It is hard to know what you’re getting because people in the Bend area sell cars for different reasons. Think about why you’ve sold cars. Did you just want something new or were there problems that you wanted to run away from. Maybe it was a little of both.

Used cars with 25,000 to 35,000 miles on them are often lease returns, corporate program cars or vehicles that have done duty in rental fleets. We feel pretty confident because they’re newer and may still be under warranty. But how well have they been maintained?

If you plan on owning a car for a long time, you’ll keep up on the maintenance so that you can avoid expensive repairs down the road. But, if you know you’re only going to have the car for two or three years, you may not be so committed to maintenance. It would be easy to think that skipping an oil change here and there wouldn’t ruin a brand new engine. Then it’ll be someone else’s problem when it comes time to pay for the damage.

It would be very tempting to skip the 30,000 mile service if you knew you’d be turning in your leased vehicle in a couple of months.

If the vehicle didn’t come with maintenance records, you need to assume the worst. Most likely the coolant system and transmission have never been serviced. The cabin air filter has probably not been changed and a fuel system cleaning may be in order.

You’ll want Wade Bryants auto repair & service center to check the air conditioning, battery, engine air filter, serpentine belt and hoses. An inspection at Wade Bryants auto repair & service center is well worth the cost.

And if your “new” used vehicle has more miles on it, an inspection is even more important. Check your owner’s manual or talk with your service advisor at Wade Bryants auto repair & service center (call 541 389 2465) about what should have been done. Please don’t forget the timing belt; that can be very expensive if it fails.

Wade Bryants auto repair & service center will help you with a plan to take care of critical services and get the rest caught up. If your budget won’t allow you to take care of everything right away, we can help you prioritize your needs and get it taken care of over the next several months. And remember to keep your maintenance records. They’ll help you get top dollar when it’s time for you to sell.

Wade Bryants auto repair & service center
324 se 9th st
Bend, Oregon 97702
541 389 2465

Share
Posted in Older Vehicles | Leave a comment

Fuel Injectors

Posted on May 23, 2011 by wade

The last new car sold with a carburetor in North America rolled out of the dealership in 1990. Since then, all new vehicles have had fuel injectors. In very simple terms, a fuel injector is a valve that squirts fuel into your engine. Your engine control computer tells the fuel injector how much gas to deliver as well as the precise time it should be delivered. Of course this happens thousands of times a minute. Fuel injection is a much more precise way of delivering fuel than carburetors. That translates into better fuel economy and power. Virtually all fuel injectors for gas engines are known as port fuel injectors because they deliver the fuel to a port just outside the cylinder. Port fuel injectors operate at about 40 to 80 pounds per square inch of pressure.

A few auto makers have introduced gas direct injection systems on some engines recently. These systems inject the gas directly into the cylinders under very high pressure – hundreds of times the pressure of port injection systems. Although more complicated, direct injection technology promises greater power with improved fuel economy, so we can expect to see more of it in the future.

As you can see, the level of precision required of your fuel injectors is very high. They need to be operating properly in order for your car to run right.

High temperatures under your hood and variations in gas quality cause fuel injectors to become fouled with wax, dirt, and carbon. Injectors can become partially clogged, preventing them from delivering the proper amount of fuel at the correct pressure. The design of each engine requires a specific spray pattern from the fuel injector that might be altered when the injector is dirty. When injectors are dirty, the fuel doesn’t burn as efficiently resulting in poor fuel economy and loss of power. So it is important to keep your fuel injectors clean.

Skilled service technicians at Wade Bryants auto repair & service center in Bend can perform a fuel system service for you. (Visit wadebryants@mechanicnet.com.) That is a fuel system service – not just fuel injector cleaning. That is because the fuel has a lot of ways to become dirty or contaminated between the gas tank and the fuel injector. A fuel system service starts with a fuel filter replacement. This filter cleans the gas as it leaves the tank. The various parts of the fuel intake system need to be cleaned from time to time to remove harmful gum, deposits and varnish. Finally, the fuel injectors are cleaned so that they operate properly and deliver the right amount of fuel at the right time.

Your Sunriver area service center uses a process for cleaning your fuel system that includes state-of-the-art cleaning chemicals as well as some old fashioned scrubbing. Proper maintenance of your fuel system means that you will spend less on gas, enjoy strong performance and prevent costly repairs down the road.

Share
Posted in Fuel System | Leave a comment

Proper Fluids for Your Vehicle

Posted on May 23, 2011 by wade

We would like to give you an update on some of the things happening in automotive fluids. You know, cars are becoming more sophisticated everyday – and fluids such as, oil, coolant and transmission fluid are becoming more specialized at about the same pace.

The do-it-yourselfer has to be pretty careful so that they do not actually harm their vehicle with the wrong type of fluid. That is why so many Oregon car owners rely on the advice of their service consultant to not only get the correct family of fluids, but to suggest the formulation that is best for their car and the way they drive.

Let’s start with engine oil. If you have been paying attention, you will have noticed a number of new oil weights on the scene in the last several years. Modern engines are built to much tighter tolerances and have very complicated valve trains. The oil must be thin enough to lubricate complicated parts when the engine is cold. The weight of an oil is expressed in terms like 20-W-50 or 5-W-30. Manufacturers recommend the weight of oil for each vehicle they make. The recommendation is based on engine design. Your Bend service center will know what weight your manufacturer recommends – and it’s important to follow those recommendations. A service adviser at Wade Bryants auto repair & service center can also offer suggestions for special formulations and can explain conventional and synthetic oils.

Antifreeze, or engine coolant, is another area that has become more complicated. For a long time, manufacturers only called for a couple of different types of coolant. Now there are several different formulations that are needed because of the different materials that manufacturers are using to build the cooling system. Using the wrong type of coolant can actually void your warranty, so you want to get that right.

Transmission fluid is beginning to be specialized as well. New transmission designs have particular requirements that mandate the use of specific formulations. Recently, new, somewhat confusing, standards for brake fluid have also been released.

Not too long ago, there was a good chance that all of the vehicles at your house would use many of the same fluids. However, as automotive technology advances, the array of basic automotive fluids you need will grow. And, some of the formulations will cost a little more. Fortunately, your Redmond service center will continue to update their training to keep pace with technology so that you’ll get the right fluids your car needs. It’s all part of the commitment your service center makes to your driving peace of mind.

Share
Posted in Fluids | Leave a comment